-
Keywords"brass"ļ¼total 110 records
-
induction soldering brass rings
Soldering brass rings Objective: To heat 1 3/4, 3 and 6 diameter brass slip rings and a sheathed copper wire assembly to 3600 F for soldering within three (3) to six (6) seconds. Currently production is accomplished by using a soldering iron and stick feedā¦
Dateļ¼2008/02/03
-
induction soldering brass bellows assembly
Soldering Brass Bellows Assembly Objective: To heat a brass bellows and end cap assembly to 450F for soldering within 20 seconds. Presently, a soldering iron is used to produce the joint between the bellows and cap. The customer requests a quality solder jā¦
Dateļ¼2008/02/03
-
induction soldering brass tubes
Soldering brass tubes Objective: Soldering two brass tubes measuring 3/4 and 1/4 together for use as cellular phone antennas. The lengths of tubes range from four (4) feet to twelve (12) feet, and must be soldered along the axial side. The joint is to be mā¦
Dateļ¼2008/02/03
-
induction brazing brass faucet
Objective Brazing two joints on a brass bathroom faucet assembly Material Brass bathroom fittings 1ā OD, brazing rings, flux Temperature 1148 F (620 C) Frequency 90 kHz Equipment ā¢ Power of 90kW induction heating system, equipped with a remote workheā¦
Dateļ¼2007/04/03
-
induction brazing brass trap block
Objective Block is heated to 1400F to braze trap tube to assemblyMaterial brass block and pre-formed tubesbraze pre-formsTemperature 1400 F (760C)Frequency 357 kHzEquipment Power of 20kW induction heating system includingā¢ Coil: custom-designed 2-turn splā¦
Dateļ¼2005/10/02
-
induction brazing brass fittings
Objective To heat brass tubing assemblies to 750C for a brazing application. The tubing diameter varies from 3 to 8 inches (76.2 to 203.2 mm) Material Brass tubing Brass flange Braze rings Braze flux Temperature 1382F (750C) Frequency ā¦
Dateļ¼2005/10/02
-
induction brazing brass fitting to copper air lines
Objective To braze brass end-connectors to copper tubes used in aircraft assembly air linesMaterial brass end connectors, copper tubes of different diametersTemperature 1400 F 750CFrequency 350 kHzEquipment Power of 6KW induction heating system, including ā¦
Dateļ¼2005/10/02
-
induction braze copper tube to brass fitting
Objective To use induction heating to braze a copper tube to a brass fitting using a preform braze wire. Processing is to occur under an atmosphere of Nitrogen and 4% Hydrogen gas. The braze preforms melt at 1190F, but the parts need to be kept below 1300Fā¦
Dateļ¼2005/10/02
-
induction annealing brass wire
Objective Continuously anneal a brass wire used in electric motors at a rate of 16.4 yds (15m) per minute to eliminate work hardening caused during the drawing process. Material Square copper wire 0.06ā (1.7mm) dia., temperature indicating paint Temperaā¦
Dateļ¼2006/10/02
-
induction annealing brass crimping
Objective To anneal a small area of an electrical contact for crimpingMaterial Brass female spade electrical contact with single transverse loop at end 0.5Āh(12.7mm) long, 0.25Āh(6.3mm) wide and 0.03Āh (0.8mm) thick, 1000oF (538oC)heat paintTemperature ā¦
Dateļ¼2006/10/02
© Copyright 2021. uihm.com All Rights Reserved.