-
Keywords"Induction Brazing"ļ¼total 222 records
-
Induction Brazing brass trap block
Objective Block is heated to 1400F to braze trap tube to assemblyMaterial brass block and pre-formed tubesbraze pre-formsTemperature 1400 F (760C)Frequency 357 kHzEquipment Power of 20kW induction heating system includingā¢ Coil: custom-designed 2-turn splā¦
Dateļ¼2005/10/02
-
Induction Brazing plumbing
Objective A copper-brass fluids union is brazed under constrained conditions (onboard a submarine), where access is limited and flame is not allowed. Material copper and brass plumbing components Temperature 750C (1380 F) Frequency 245 kHz Equipment Poā¦
Dateļ¼2005/10/02
-
Induction Brazing carbide
Objective Braze a carbide wear pad to steel for automated surgical forceps Material Steel assembly 1/2ā (127 mm) long, 1/8 ā (3.175 mm)cross section Carbide wear pad Braze alloy Temperature 1350-1400 F (732- 760 C) Frequency 313 kHz Equipment Poā¦
Dateļ¼2005/10/02
-
Induction Brazing steel-carbide tool
Objective Provide a solution to this steel-carbide brazing applicationMaterial ā¢ Body 10mm; carbide tip 57 x 35 x 3 mmā¢ Braze shimā¢ Braze flux whiteTemperature 750C (1382F)Frequency 152 kHzEquipment Power of 10kW induction heating system, equipped with ā¦
Dateļ¼2005/10/02
-
Induction Brazing steel to steel
Objective To braze O-ring Face (ORFS) sleeve or male connector to a steel tube. Material ā¢ Steel tube, 1 inch (2.54 cm) OD ā¢ O-ring Face Seal sleeve and a male connector fittings ā¢ Preform braze rings ā¢ White SureFlow flux ā¢ Steel support mandrelā¦
Dateļ¼2005/10/02
-
Induction Brazing carbide to steel
Objective Braze a carbide sleeve to a steel āTā shank Material 2.0ā (51mm) OD carbide sleeve, 1.0ā (25.5mm) high braze joint, 1.5 ā (38 mm) steel āTā , 50% silver braze ring Temperature 1292 F (700 C) Frequency 257 kHz Equipment ā¢ Power of 10 kā¦
Dateļ¼2005/10/02
-
Induction Brazing copper to copper
Objective To braze copper to copper bus bar assemblies together Material ā¢ 2 copper bus bars 6ā (152.4mm) wide, 2ā (609.6mm)long, 2 copper bars 6ā(152.4mm) wide, 18ā (457.2)long & 3/8ā (9.65mm) thick ā¢ braze shim preforms and white flux Tempeā¦
Dateļ¼2005/10/02
-
Induction Brazing stainless steel
Objective 1st Application: Braze hub assembly to needle holder 2nd Application: Braze Large tube to ring joint Material 1st Application: Steel hub assembly and needle 0.1ā dia (2.5mm) 2nd Application: Steel tube 1ā OD (25.4 mm) and ring Temperature 1ā¦
Dateļ¼2005/10/02
-
Induction Brazing copper tube & pipe
Objective Braze brass fitting with o-ring to various diameters of copper tube. Material Various copper tubes ranging from 3/8ā to 7/8ā diameter and 2-3ā long, female brass fittings with o-ring, silver solder rings and glass beaker. Temperature 1300 F ā¦
Dateļ¼2005/10/02
-
Induction Brazing carbide teeth to steel pipe
Objective Brazing carbide teeth to a steel jaw in less than 5 minutes Material Steel pipe jaw, 0.5ā (12.7mm) dia, 1.25ā (31.75mm) long, 0.25ā (6.35mm) thick carbide teeth, black flux and silver copper braze shims Temperature 1292F (700C) Frequency 25ā¦
Dateļ¼2005/10/02
© Copyright 2021. uihm.com All Rights Reserved.