-
Keywords"brazing"，total 336 records
-
induction brazing steel-carbide tool
Objective Provide a solution to this steel-carbide brazing applicationMaterial • Body 10mm; carbide tip 57 x 35 x 3 mm• Braze shim• Braze flux whiteTemperature 750C (1382F)Frequency 152 kHzEquipment Power of 10kW induction heating system, equipped with …
Date：2005/10/02
-
induction brazing steel to steel
Objective To braze O-ring Face (ORFS) sleeve or male connector to a steel tube. Material • Steel tube, 1 inch (2.54 cm) OD • O-ring Face Seal sleeve and a male connector fittings • Preform braze rings • White SureFlow flux • Steel support mandrel…
Date：2005/10/02
-
induction brazing carbide to steel
Objective Braze a carbide sleeve to a steel ‘T’ shank Material 2.0” (51mm) OD carbide sleeve, 1.0” (25.5mm) high braze joint, 1.5 ” (38 mm) steel ‘T’ , 50% silver braze ring Temperature 1292 F (700 C) Frequency 257 kHz Equipment • Power of 10 k…
Date：2005/10/02
-
induction brazing copper to copper
Objective To braze copper to copper bus bar assemblies together Material • 2 copper bus bars 6” (152.4mm) wide, 2’ (609.6mm)long, 2 copper bars 6”(152.4mm) wide, 18” (457.2)long & 3/8” (9.65mm) thick • braze shim preforms and white flux Tempe…
Date：2005/10/02
-
induction brazing stainless steel
Objective 1st Application: Braze hub assembly to needle holder 2nd Application: Braze Large tube to ring joint Material 1st Application: Steel hub assembly and needle 0.1” dia (2.5mm) 2nd Application: Steel tube 1” OD (25.4 mm) and ring Temperature 1…
Date：2005/10/02
-
induction brazing copper tube & pipe
Objective Braze brass fitting with o-ring to various diameters of copper tube. Material Various copper tubes ranging from 3/8” to 7/8” diameter and 2-3’ long, female brass fittings with o-ring, silver solder rings and glass beaker. Temperature 1300 F …
Date：2005/10/02
-
induction brazing carbide teeth to steel pipe
Objective Brazing carbide teeth to a steel jaw in less than 5 minutes Material Steel pipe jaw, 0.5” (12.7mm) dia, 1.25” (31.75mm) long, 0.25” (6.35mm) thick carbide teeth, black flux and silver copper braze shims Temperature 1292F (700C) Frequency 25…
Date：2005/10/02
-
induction brazing bourdon tube
Objective To braze a thin copper oval tube to a brass fitting at 1400 F and to cap the other end of the copper tube with a brass plate.Material Brass fitting – 0.875 in2 and 2.5 in long (22mm2 x 64mm) Copper tube 0.01 in (0.254mm) wall Brass plate 0.10 i…
Date：2005/10/02
-
induction brazing brass fittings
Objective To heat brass tubing assemblies to 750C for a brazing application. The tubing diameter varies from 3 to 8 inches (76.2 to 203.2 mm) Material Brass tubing Brass flange Braze rings Braze flux Temperature 1382F (750C) Frequency …
Date：2005/10/02
-
induction brazing carbide shaft to steel tube
Objective Braze a carbide shaft to a steel tube Material Carbide shaft 1/8” to 1” diameter (varying sizes) Steel tube 3/8” to 1 ” OD Silver solder braze Temperature indicating paint Temperature 1400 F for 60 seconds Frequency 220 kHz Equipment Pow…
Date：2005/10/02
© Copyright 2024. uihm.com All Rights Reserved.
