-
Keywords"to"，total 608 records
-
induction brazing steel-carbide tool
Objective Provide a solution to this steel-carbide brazing applicationMaterial • Body 10mm; carbide tip 57 x 35 x 3 mm• Braze shim• Braze flux whiteTemperature 750C (1382F)Frequency 152 kHzEquipment Power of 10kW induction heating system, equipped with …
Date：2005/10/02
-
induction brazing steel to steel
Objective To braze O-ring Face (ORFS) sleeve or male connector to a steel tube. Material • Steel tube, 1 inch (2.54 cm) OD • O-ring Face Seal sleeve and a male connector fittings • Preform braze rings • White SureFlow flux • Steel support mandrel…
Date：2005/10/02
-
induction brazing carbide to steel
Objective Braze a carbide sleeve to a steel ‘T’ shank Material 2.0” (51mm) OD carbide sleeve, 1.0” (25.5mm) high braze joint, 1.5 ” (38 mm) steel ‘T’ , 50% silver braze ring Temperature 1292 F (700 C) Frequency 257 kHz Equipment • Power of 10 k…
Date：2005/10/02
-
induction brazing copper to copper
Objective To braze copper to copper bus bar assemblies together Material • 2 copper bus bars 6” (152.4mm) wide, 2’ (609.6mm)long, 2 copper bars 6”(152.4mm) wide, 18” (457.2)long & 3/8” (9.65mm) thick • braze shim preforms and white flux Tempe…
Date：2005/10/02
-
induction brazing carbide teeth to steel pipe
Objective Brazing carbide teeth to a steel jaw in less than 5 minutes Material Steel pipe jaw, 0.5” (12.7mm) dia, 1.25” (31.75mm) long, 0.25” (6.35mm) thick carbide teeth, black flux and silver copper braze shims Temperature 1292F (700C) Frequency 25…
Date：2005/10/02
-
induction brazing carbide shaft to steel tube
Objective Braze a carbide shaft to a steel tube Material Carbide shaft 1/8” to 1” diameter (varying sizes) Steel tube 3/8” to 1 ” OD Silver solder braze Temperature indicating paint Temperature 1400 F for 60 seconds Frequency 220 kHz Equipment Pow…
Date：2005/10/02
-
induction brazing carbide tool
Objective Braze carbide rotary file assemblies with uniform concentricity in an aerospace application Material • Carbide blank • High speed steel shank • Temperature indicating paint • Braze shim and black flux Temperature 1400F (760C) Frequency …
Date：2005/10/02
-
induction brazing cutting tool
Objective To braze cone and shaft for a cutting tool Material Customer supplied parts Temperature indicating paint Braze preforms Temperature 1300 – 1400 F (704 – 760 C) Frequency 235 kHz Equipment Power of 6 kW, 150-400 kHz induction h…
Date：2005/10/02
-
induction brazing brass fitting to copper air lines
Objective To braze brass end-connectors to copper tubes used in aircraft assembly air linesMaterial brass end connectors, copper tubes of different diametersTemperature 1400 F 750CFrequency 350 kHzEquipment Power of 6KW induction heating system, including …
Date：2005/10/02
-
induction braze copper tube to brass fitting
Objective To use induction heating to braze a copper tube to a brass fitting using a preform braze wire. Processing is to occur under an atmosphere of Nitrogen and 4% Hydrogen gas. The braze preforms melt at 1190F, but the parts need to be kept below 1300F…
Date：2005/10/02
© Copyright 2024. uihm.com All Rights Reserved.
