-
Keywords"induction"ļ¼total 2889 records
-
induction brazing copper tube
Objective To braze a copper tube ( 3/8ā³ OD by 2-4ā³ long) into a 3/8ā³ fitting in less than 10 seconds. Heating must take place in a channel type coil to allow for easy loading of parts. Material Copper Tubing and Fitting with Braze and Stay Silv Whiteā¦
Dateļ¼2005/10/02
-
induction brazing carbide tips on drill bits
Objective To braze carbide cutting tips to drill bits ranging in size from 0.5ā³ to 1.5ā³ in diameter. The brazing takes place at 1900F and is presently done in 11 seconds for the 0.5ā³ diameter bit and 39 seconds for the 1.5ā³ diameter bit. Customer goalsā¦
Dateļ¼2005/10/02
-
induction brazing steel tube with copper ring
Objective To heat an oil suction assembly (steel tubing and filter cap) to 1,850F (1010C) within 15 seconds for a brazing application. Material 0.125ā (3.2mm) diameter steel tube and filter cap assembly, high temperature brazing flux, copper ring. Tempeā¦
Dateļ¼2005/10/02
-
induction brazing turbine blades
Objective To heat an inconel turbine blade in a vacuum to 2000F and hold temperature for five minutes for a nickel brazing application. Material Inconel turbine blades, nickel metering plates, nickel braze Temperature 2050F Frequency 20 kHz Equipment Aā¦
Dateļ¼2005/10/02
-
induction brazing steel fitting
Objective To heat a steel hydraulic hose fitting in an inert atmosphere to 2200F within 7 seconds for brazing without any carbon buildup. Material Three-opening steel hydraulic fitting, pure copper braze paste Temperature 2200F Frequency 273 kHz Equipmā¦
Dateļ¼2005/10/02
-
induction brazing steel conduit
Objective To heat a stainless steel conduit, ferrule and elbow assembly to 1400F (760C) within 20 seconds for brazing. Material 6ā(152.4mm)long x 0.5ā(12.7mm) diameter stainless steel conduit, 0.5ā(12.7mm) long x 0.5ā(12.7mm) diameter ferrule, 2ā(50.ā¦
Dateļ¼2005/10/02
-
induction annealing steel tubes
Objective To heat steel tubes to 2000 F (1093 C) in an inert atmosphere Material 0.1ā (2.54mm) diameter stainless steel tube Temperature 2000 F Frequency 333 kHz Equipment ā¢ 10 kW induction heating system, equipped with a remote workhead containingā¦
Dateļ¼2006/10/02
-
induction annealing motor shaft
Objective Annealing the end of a steel hydraulic motor shaft prior to machining Material .75ā (19mm) diameter steel rod, 6ā (152.4mm) long with a keyway at the end Temperature 1350 F (732 C) Frequency 359 kHz Equipment ā¢ UM-06A-UHF induction heatingā¦
Dateļ¼2006/10/02
-
induction annealing aluminum tubing
Objective Annealing aluminum fuel tank fill neck to 650 F (343 C) Material Aluminum fill neck 2.5ā (63.5mm) diameter, 14ā (35.5cm) long Temperature 650 F (343 C) Frequency 85 kHz Equipment ā¢ 40kW induction heating system, equipped with a remote workā¦
Dateļ¼2006/10/02
-
induction annealing brass wire
Objective Continuously anneal a brass wire used in electric motors at a rate of 16.4 yds (15m) per minute to eliminate work hardening caused during the drawing process. Material Square copper wire 0.06ā (1.7mm) dia., temperature indicating paint Temperaā¦
Dateļ¼2006/10/02
© Copyright 2021. uihm.com All Rights Reserved.